SERVICES-SYSTEMS SCOPE
ENGINERING SERVICES
1. Data accumulation for electrical & allied systems in our scope through meetings with client & other consultants.
2. Load calculations & assessment of actual demand, possible maximum demands, rating of transformer, substation requirements, and D. G. set requirements.
3. Liaisoning work with statutory agencies is not Undertake by us.
4. Detail engineering of the power system like distribution cables, panels & Distribution boards, cable sizing, power outlets, power wiring. Layouts for the power distribution system. Single line diagrams.
5. Lighting scheme design for internal & external lighting, lighting layouts with SLDs. Selection of fixtures & detailing of mounting.
6. Detail engineering & layout drawings for lightening protection & Earthing systems.
7. Detailing & drawings for communication, fire detection & alarm systems security system if any.
8. Preparation of Technical specification for equipment and Works. Preparation of bill quantities & estimates based on BOQ & specifications.
9. Floating Inquiries /tenders consisting of general terms of contract Technical Specifications schedule of quantities Drawings.
10. Technical & commercial comparison of quotes for above recommendation, negotiations, order drafts etc.
11. Bar chart preparation or work schedule preparation on this basis of client inputs.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
SUPERVISION
1. Shop testing of panels, transformer etc.
2. Regular site visits to sites monthly / fortnightly depending on the clients /work requirement, for quality survey of work and material progress review meeting.
3. Feedback to client about progress / delays, probable reasons, obstacles, certification of bills.
4. Measurement & billing help to client engineer / representative. Certification of bills.
5. Testing commissioning checks and witnessing testing and commissioning.
SUBSTATION DESIGN
- Protection and Metering SLO.
- Substation Layout Plan and Sections.
- Line Diagrams and Construction Drawings.
- Substation Clearance Diagram
- Erection Key Diagram.
- Earthing & Lightning Protection.
- Lighting System Design.
- Cable Routing and Schedule.
- Control Room Equipment Layout.
- Battery and LVAC System.
- Substation Automation.
- SCADA System Design.
- Project Bill of Materials
- Grounding Systems Design.
Electrical Services – H.T Side
- High Tension Line Work up to 132 kV
- Overhead/Underground Independent feeder line.
- Power Transformer/V.C.B/H.T Panel/Metering Panels.
- H.T Cable Joints with Heat Shrinkable Cable Jointing Kits.
- H-Pole with P.C.C Poles or Steel Tubular Poles.
- A.B. Switch & D.O. Fuses/C.T & P.T.
- H.T XLPE Cable/A.C.S.R/Aerial Bunched Cable(A.B.C).
- Chemical/Plate Earthing.
- GI/Copper Strip &Wire.
- Laisioning Work as per SEB rules & regulations.
LIGHTING SERVICES
- Industrial & Commercial Building Interior Lighting.
- Outdoor Facilities Lighting.
- Street Lighting.
- Parking Lot Lighting.
- Emergency Lighting Indoor LED and incandescent lighting.
- Overhead fixture installation.
- Recessed lighting.
- Under cabinet lighting.
- Outdoor structural lighting.
- Landscape lighting.
- Outdoor security lighting.
ELECTRICAL SYSTEM STUDIES
- Specialized Studies of System Losses / Power Factor.
- Power analysis and Harmonic studies
- Limited System & Regional Load Flow Studies.
- Long Range System Studies.
- Construction Work Plans.
- Short Circuit Studies.
- Protection Coordination Studies.
- Feasibility Studies for Conceptual Power Systems.
FABRICATION SERVICES
- I-Beam Track Conveyor Installation
- Equan-super Track Conveyor Installation
- All Types Slat Conveyor Installation
- M.s. & S.s Fabrication
- Structure Fabrication
- Heavy Fabrication
- Industrial Fabrication & Maintaince Work
- Shed Demolishing Service
- Car Parking Roofing Shed Contractor
- Industrial Shed Contractor
- Air, Water, Fuel pipeline Work.
SOFTWARE SUPPORT
DRAFTING & DETAILING AUTO CAD & EPLAN
- Designing
- Efficient Layout Planning.
- Co-ordinated system layout drawings with drawing detailing and interference check.
- Including shop drawings.
- Schematic layouts & loop drawing.
- Project Planning, Scheduling, & Monitoring Microsoft Projects & Excel.
- Documentation of Targets.
- Structuring and Scheduling of Project.
- Planning of Logistics & Services.
- Ensuring Timely Delivery and Installation of Equipment at site.
OTHER WORKS
- Installation & Commissioning up to 132 KVA system.
- Repair & Maintenance up to 132 KVA system.
- We also works on Residential & industrial fire alarms systems. Installation of MCP, Hooters, fume detector, smoke detector, beam detector etc, and commissioning of fire alarms system.
- Instrumentation works like Design & develop control systems, Maintain the existing control systems, manage the control systems.
